135L Industrial Ultrasonic Cleaning Bath With Heater and Timer
What is Ultrasonic Cleaning?
Ultrasonic cleaning uses ultrasonic energy in an immersion cleaning tank to assist in the removal of tenacious or stubborn soils from parts. An ultrasonic system always consists of at least three main components:
1. A tank to hold the cleaning fluid and the dirty parts
2. A generator to transform the line voltage into an ultrasonic signal
3. Transducers to convert the ultrasonic electrical signal into mechanical energy
How does Ultrasonic Cleaning Work?
An ultrasonic system works by inducing controlled cavitation in the cleaning fluid. Cavitation refers to microscopic voids or "bubbles" that form when the transducers emit sufficient ultrasonic energy into the fluid. The cavitation bubbles form relatively slowly and then collapse suddenly, releasing tremendous energy against the surfaces of objects immersed in the tank that ‘scrubs’ hard to remove soils from the parts.
Application
Industrial ultrasonic cleaner are suitable to clean irregular and complex specialized instruments, components and PCBs of sundry shops, workshops, factories etc.You could check the comparison from the picture below.
· Jewelry especially gold, silver & platinum
· Watchstraps
· Coins and other collectibles
· PCB Boards etc
· Engine/Model parts
· Toothbrushes & Dentures
· Electrical components
· Make-up cases
· Diesel injection pumps
· Printer heads and toner cartridges
· Motorcycle radiators
· Vehicle differentials
· Milking parlor equipment·
· Golf clubs&grips&golf balls
. Horse bits&stirrups &horse brasses
· Tattoo needles· Surgical equipment
Why you choose us:
- Are more effective at removing contaminants;
- Are quicker to get a good cleaning effect;
- Save labor time of employees (and subsequent labor cost);
- can heat the cleaning solutions to a suitable cleaning temperature so as to enhance the cleaning efficiency;
- Have a digital controller of high-precision and a long service-life;· Are of high performance;
- reduce chemicals in the cleaned stuffs;· Are environment friendly because of its recyclability
- there is no MOQ in our factory.
- Could customized the model for you.
- 1year warranty.
- engineer's technology support
- heating and power adjustable
Specification
| Model: | DK-3610D |
| Tank Size(mm): | 600*500*450(L*W*H) |
| Overall Size(mm): | 870*680*900(L*W*H) |
| Capacity: | 135L |
| Frequency(KHz): | 28/40 |
| Ultrasonic Power(W): | 0~1800 |
| Heating Capacity(W): | 6000 |
| Timing Range(min:secs): | 1~99 |
| Temperature Range(℃) | 0~80 |
| Water Drainage | Yes |
Plug
There are all kinds of plugs, such as UL,SAA,VDE,JAPAN OLUGE,SABS,THE UK PLUGE etc.
Certifications
All Dekang’s standard products have achieved most international standards, such as CE certification, RoHS certification, FCC certification etc. Besides, all no-standard products also can satisfy all requirements of these most international standards.
How to use it
1. Fill the stainless steel tank with cleaning solution; turn the single phase switch or three phases switch on; After power-on, the LED display of the temperature displays the actual environmental temperature; while the LED display of time displays 3 minutes (default ultrasonic time).
2. Temperature setting: Press “temperature-/temperature+”shortly at a time means time increase/ reduce 1℃ at a time, press and hold there means time will increase/decrease by 10℃ .
Note: Usually, the best cleaning temperature is within 40℃ to 60℃. The temperature displayed is the real temperature. The default value of the temperature is 0℃. When you set temperature, the heating function can not be started unless the set temperature is higher than the environmental temperature and the “Heating” button is pressed after the temperature setting. When the real temperature is higher than the set temperature, the indicator of heating will turn off. However, the heating function would not be turned off automatically if the ultrasonic cleaning still works, it will start again when the water temperature is lower than the set temperature. In this case, you can only press “Heating” to turn off heating function. However, if the ultrasonic cleaning time runs out, the heating function will stop automatically.
3. Time setting: Press the “TIME-/ TIME+ ”shortly at a time means time increase/reduce 1min at a time, press and hold means time will increase/reduce by 10mins continuously. The cleaning stops when the timer counts down to 00:00. If the unit needs to be stopped before the timer runs up, press “Ultrasonic” button.
4. After time and temperature setting, press “Ultrasonic” or ”Heating” button to start both functions. Press “Ultrasonic ” or ”Heating” button again, the Ultrasonic or heating function will stop.
5. Power Controller: the power can be adjusted among 0% and 100%. Users can adjust the power value randomly based on the characters of the stuffs to be cleaned.
6. “Filter”: the filtration system with a sparger can be started or stopped by pressing “Filter” button.
Empty the tank and clean both the outside and inside of the cleaner with a clean and dry cloth for next use.
Express
Include: TNT, UPS, FedEx, EMS, DHL, ect. Also you could pick the goods by your courier and we wouldn't charge it.
Product Tags:
|
|
135L Industrial Ultrasonic Washing Machine With Heater And Timer Images
|
